Our Products

Search Product :

Aggregate	Balance
Bitumen	Cement
Cement Concrete	Compression Testing Machine
General	New Release
Sieves	Soil
Survey

Bitumen

Bitumen
Product code : ASEW_224

ASEW -224
Centrifuge Extractor, Hand operated ASTM D 2172, AASHTO T058.T0164
This used for the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. The centrifuge extractor is a safe, portable, corrosion-resistant module which can be used both in the field and the laboratory; It consists of a removable cast aluminium rotor bowl mounted on a vertical shaft. A filter paper disc is pressed in between the rotor bowl and cover plate by a knurled nut. The bowl assembly is enclosed is a housing mounted on a cast aluminium body. The gears operate in oil bath assembly is enclosed is a housing mounted on a cast aluminium body. The gears operate in oil bath with splash lubrication. Complete with 25 filter discs.

ASEW -225
Centrifuge Extractor, Electrically ASTM D 2172, AASHTO T058.T0164
Similar to above, but is operated by a motor coupled to a gear box and the drive is through a strip pulley. The motor part can be disconnected and the unit can be operated manually in case of power failure. The motor drive gives 3500 r.p.m. to the rotor bowl. Operation on 230 V, single phase, 50 cycles, A.C. supply.

Bitumen
Product code : ASEW_222

ASEW -222
Marshall Stability and compaction AS I'M 1559, BS598-107
* 30 KN (3000 kg) capacities
* Platen rate 50.8 mm per minute
* Safety cut-out switch for platen travel

a. The load frame, confirming to British Standard BS 594 : 1973 and ASTM D 1559, comprises which houses a geared screw jack and motor drive mechanism, all enclosed within a rigid sheet steel frame. Automatic cut out prevents platen over run on the down ward & upward travel. Suitable for operation on 230 volts, single phase, 50 cycles, A.C. supply.
b. Compaction Mould comprising filling colour, mould body and base plate. Manufactured from steel
c. Compaction pedestal comprising of a hard wood block with a steel plate. Complete with specimen holder semi-circular base and a circular top to hold the specimen mould in place during compaction of the specimen.
d. Compaction Hammer designed for use with the compaction pedestal and mould. The hammer has a 4.5 kg weight which has a free fall of 457 mm.
e.Breaking head assembly, complete with gauge disc and flow meter pedestal.
f. Load transfer bar
g. Specimen extractor
h. Flow meter (dial gauge) graduated 0.01 mm x 25 mm travel
i. Mixing bowl fitted with handle
j. Mixing trowel

Accessories:
a. High sensitivity Proving ring 2500 kg capacity fitted with 0.002 mm dial gauge. Complete in a nice wooden carrying case.
b. Do-but 50 KN.

ASEW -223
Modified Marshal Stability Test Apparatus:
* 100 KN (10,000kg) capacity
* Platen rate 50.8 mm per minute
* Safety cut-out switch for platen travel

Complete with Marshal Mould 152.4 mm dia-3, Rammer 10.2 kg-2 Nos. Pedestal for 152.4 mm dia with holding arrangement for Rammer. Breaking head assembly, Load transfer bar, Specimen extractor, Flow meter (Dial gauge) 0.01 mm x 25 mm travel. Mixing bowl with handles and Mixing trowel

Accessories:
High sensitivity Proving ring 50 KN capacity with calibration certificate in a nice wooden carrying case

Bitumen
Product code : ASEW_219A

ASEW -219
DUCTILITY TESTING MACHINE: IS: 1208 ASTMD113, AASHTOT51
Mould-3 - Nos. Made of brass/gunmetal mounted on a base plate. Each mould has two end clips, two sides with knurled screws and side support for proper assembly on the base plate. One spare mould with base plate for casting the specimen is also supplied.

Water Bath Thermostatically Controlled: A bath maintained with ± 0.1 °C of the specified test temperature, containing not less than 10lt. of water, the specimen being immersed to a depth of not less than 100 mm and supported on a perforated shelf not less than 50 mm from the bottom of the bath.

Testing Machine: The machine has two rate of travel, namely 5 cms per minute and 1 cm per minute. A clutch arrangement is provided by which the movement of the movable bracket can be arrested or restarted without switching off the motor. A scale on the top edge of the bath makes it easy for the operator to observe the progress of the test. Machine accommodates three individual specimens. A quick release mechanism permits the operator to move the carriage to any desired position on the track. An automatic cut off prevents over runs. Immersion heater also provided.

A three wire cord with plug is furnished with the bath. The control panel is recessed. Controls consist of a temperature, an on-offline switch which controls all power to the bath, and pilot light which indicates when the heater is energized. Operation on 230 volts, single phase, 50 cycles, A.C. supply.

Spares:
a. Ductility Mould with base plate made of gunmetal.

ASEW -219 (A)
DUCTILITY TESTING MACHINE with Digital temperature controller-cum-display electrically operated.

Bitumen
Product code : ASEW_211

ASEW -210
Hydraulic Jack, Hand operated: Remote control type.
Hydraulic jacks are of multipurpose utility i.e. application of loads while engaged in field investigation, determination of load carrying capacity of piles in the field, tensioning of wires in pre-cast structures, loading of members of any structure for deformation characteristics etc. The Jacks are supplied complete with manually operated pumping units fitted with Bourdon tube type Hydraulic pressure gauge and a copper connecting tube or rubber flexible hose pipe.

Lift of the ram - 150 mm
Pressure gauge - MASTAAVIKA
(Pressure gauge have normally 200 divisions for fully capacity, e.g. 100 tonne x 500 kg divisions).

ASEW -211
Hydraulic Jacks, Bottle TYPE
Hydraulic Lifting Jacks-Complete with integral Pumping unit. Release valve provided on the base plate. Complete with operating handle.
Hydraulic lift - 150 mm and Extension
Screw - 150 mm

All Jacks are without pressure gauge,

Accessories: Hydraulic Pressure Gauge

Bitumen
Product code : ASEW_218

ASEW -217
Softening Point apparatus (Ring & Ball), IS: 1205, BS2000 58, ASTMD36, and AASHTOT53.
Used for the determination of the softening point of bitumen. Consists of: Two steel balls; each 9.5 mm in dia. Brass rings Two; tapered of brass. Ball Guide Two Ring Holder One Bath Beaker of heat resistant glass, I.D. 8.5 cms and depth 12 cms approx.

ASEW -218
Ring & Ball Apparatus, electrically heating
Similar to ASEW-217, but supplied with a heating plate with an energy regulator which permits fine regulation of temperature. In addition, there is an electrically operated Stirrer mounted on a stand with chuck and glass rod or aluminium rod and for stirring the water in the water bath. Operation on 230 V, single phase, 50 cycles, A.C. supply.

Bitumen
Product code : ASEW_221

Bench-mounting mixer: This mixer has two speed constant mesh gear box driven by an electric motor fully enclosed within the transmission case. The low speed drive automatically comes into action when either the high or intermediate speed is disengaged on light loads, speed changes may be made without switching off. A gear train to provided smooth gear change and also protect the transmission mechanism. Ball bearings are used throughout which, together with all gears, run in a special lubricant requiring no attention for several years. All the mechanism from the beater shaft to the motor is enclosed. Supplied complete stainless steel bowl fitted with handle, beater, hook and heating jacket.
Motor rating: Operation: 230 volts, single phase, 50 cycles, A.C. supply.

Bitumen
Product code : ASEW_235

Small Laboratory Jaw Crusher The 'ASEW laboratory crusher is designed to speed up the crushing of aggregates, ores, minerals, coal, coke, chemicals and other similar materials. It is compact and of rugged construction for general laboratory or small pilot plant operation.
Two jaws of manganese steel are provided in the jaw crusher. The moveable jaw produces two blows for every revolution. Thus reducing over sizing to a minimum. A combination of forward and downward stroked with a rocking action exerts pressure on the coarser material, yet permits the finished material to pass through the jaws. A hopper is provided at the top for feeding materials. The smooth jaws ensure a uniform product and easy cleaning is possible.
Jaw size : 100 x150 mm Max. Size of fed : 50 mm (approx) Product discharge size : 5 mm to 15 mm. Capacity : 100 to 200 kg. (Based on material) Operation : 40V, 3 ph. 50 Hz. A.C.
Complete with a 3 H.P. motor, a starter, ‘V” belt pulley drive and mounting. Lab-Pulverizer

ASEW -236 Jaw Crusher: Medium similar to ASEW 202, but Jaw size : 150 X 200 mm Max. size of feed : 100 mm (approx) Product discharge size : 5 mm to 20 mm. Capacity : 250 to 400 kg. (Based on material) Operation : 440V, 3 ph. 50 Hz. A.C.
Spares: Pair of Jaw 100 mm x 150 mm Pair of Jaw 150 mm x 200 mm

Bitumen
Product code : ASEW_220

ASEW -219
DUCTILITY TESTING MACHINE: IS: 1208 ASTMD113, AASHTOT51
Mould-3 - Nos. Made of brass/gunmetal mounted on a base plate. Each mould has two end clips, two sides with knurled screws and side support for proper assembly on the base plate. One spare mould with base plate for casting the specimen is also supplied.

Water Bath Thermostatically Controlled: A bath maintained with ± 0.1 °C of the specified test temperature, containing not less than 10lt. of water, the specimen being immersed to a depth of not less than 100 mm and supported on a perforated shelf not less than 50 mm from the bottom of the bath.

Testing Machine: The machine has two rate of travel, namely 5 cms per minute and 1 cm per minute. A clutch arrangement is provided by which the movement of the movable bracket can be arrested or restarted without switching off the motor. A scale on the top edge of the bath makes it easy for the operator to observe the progress of the test. Machine accommodates three individual specimens. A quick release mechanism permits the operator to move the carriage to any desired position on the track. An automatic cut off prevents over runs. Immersion heater also provided.

A three wire cord with plug is furnished with the bath. The control panel is recessed. Controls consist of a temperature, an on-offline switch which controls all power to the bath, and pilot light which indicates when the heater is energized. Operation on 230 volts, single phase, 50 cycles, A.C. supply.

Spares:
a. Ductility Mould with base plate made of gunmetal.

ASEW -219 (A)
DUCTILITY TESTING MACHINE with Digital temperature controller-cum-display electrically operated.

Showing 1 - 8 of 13