|
|
Aggregate |
|
Aggregate
Product code : ASEW_194
ASEW -191
Los Angles abrasion testing machine: 2386 (P-IV), ASTMC131, C535
Consists of a hollow steel cylinder, close at both ends, having an inside diameter of 700 mm and an inside length of 500mm. The cylinder mounted on a sturdy frame on ball bearings. The opening shall be closed dust-tight with a removable cover bolted in place. A detachable shelf which extends through of the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 r.p.m by an electric motor through a heavy duty reduction gear.
Supplied complete with a tray for collection of the material
Accessories
Abrasive charge: Consists of set of 12 Nos cast iron spheres or steel spheres (Hardened steel balls) approximately 48 mm in diameter, each weighing between 390 and 445 gram.
|
|
Aggregate
Product code : ASEW_209
ASEW -209
Sand absorption cone and tamper: Consists of a conical metal mould and a metal tamping rod having circular tamping face 25 mm dia as per ASTM C 128, AASHO.T84
|
|
Aggregate
Product code : ASEW_206
Cylindrical Metal Measures: IS: 2386 (Pat –III). Made of heavy gauge sheet fitter with handles.
Nominal capacity |
I Dia |
I height |
Thickness |
3 litre |
15 cms |
17 cms |
3.15 mm |
15 litre |
25 cms |
30 cms |
4.00 mm |
30 litre |
35 cms |
31 cms |
5.00 mm |
|
|
Aggregate
Product code : ASEW_200
ASEW -198
Riffle Sample Divider: IS: 1607, 2720; ASTM CI36, D421, D422, D427, D4517, D452, D457, D806, D4318, BS: 812 (partl03), 1377, AASHTO
T27, T87
Consists of a metal box fitted with a series of chutes of equal width which discharges the material alternatively in opposite directions into separate pans. The chutes of the riffle are steep enough to allow rapid flowing of the material,
a. Slot width-13 mm
No. of slots-14
Supplied complete with two pans and one scoop
ASEW -199
Riffle sample divider
b. Slot width 25 mm
No. of slots-16
Complete with two pans and one scoop.
ASEW -200
Riffle Sample divider
c. Slot width 50mm
No. of slots-10
Complete with two pans and one scoop.
ASEW -201
Riffle Sample divider
d. Slot width 40mm
No. of slots-10
Complete with two pans and one scoop.
|
|
Aggregate
Product code : ASEW_188
ASEW -187
Aggregate Crushing Value test apparatus: IS: 2386 (Part IV) Consists of a 15 cms diameter open-ended steel cylinder, with plunger and base plate. Complete with a tamping rod of circular cross-section 16 mm in diameter and 45 to 60 cms long, rounded at one end.
ASEW -188
10% Fine Value apparatus as per IS: 2386 (p-iv) with tamping rod and measure.
ASEW -188
Aggregate Crushing Value test apparatus IS: 2386(P-iv) BS812 Similar to ASEW-187, but 75 mm dia cylinder.
Accessories:
Cylindrical metal measure 11.5 cms diameter and 18 cms height fitted with handles.
|
|
Aggregate
Product code : ASEW_207
ASEW – 207
Pycnometer of about 1 Kg capacity fitted with cone, locking ring with rubber seal as per IS: 2386 (Part-Ill)
|
|
Aggregate
Product code : ASEW_204
ASEW – 204
Length Gauge: IS 2386 (Part – 1) Constructed from steel, mounted on hardwood base
SPECIFIC GRAVITY, DENSITY VOIDS ABSORPTION & BULKING
|
|
Aggregate
Product code : ASEW_185
ASEW -185
Aggregate Impact Tester: IS: 2386 (Part IV), BS812
Determining the aggregate impact value of coarse aggregate. Consists of a base weighing between 22-30 kg with a lower surface of not less than 30 cms and support columns to form a rigid frame work around quick release trigger mechanism to ensure an effective free fall of the hammer during test. The free fall can be adjusted through 380+-5.0 mm. The hammer is provided with a locking arrangement.
A metal tup (hammer) weighing 13.5 to 14.0 kg, the lower end of in cylindrical shape, 100 mm in diameter and 5 cm long with a 2 mm chamfer at the lower edge, and case hardened.
ASEW -186
Aggregate Impact tester with automatic blow counter as per IS: 2386 9 (P-IV)
Spares
* Automatic blow counter
* Tamping Rod
|
|
|
|
|
